If the multi-functional concrete mixer fails, it will not cause harm to the vehicle itself. More importantly, the concrete in the mixer truck will also be affected. If the concrete solidifies due to the fault of the multi-functional concrete mixer, it will cause extraordinary losses. Therefore, in order to avoid this situation, when the concrete mixer truck is found to have fault When the fault occurs, it is necessary to find out the fault point and solve it in time.
一、罐体转动工作原理
1、 Working principle of can body rotation
发动机取力器——传动轴——油泵——马达——减速机——罐体转动
Engine power take-off - transmission shaft - oil pump - motor - reducer - can body rotation
二、原因分析
2、 Cause analysis
导致多功能混凝土搅拌车搅拌罐停转主要有以下原因:
The main reasons for the stop of mixing tank of multi-functional concrete mixer are as follows:
1.发动机故障:发动机无法启动、取力器损坏等原因
1. Engine failure: the engine cannot be started and the power take-off is damaged
2.上装故障:传动轴损坏、油泵故障、液压油过脏或油量不足、马达故障、减速机故障、操纵杆松脱等原因。
2. Upper mounting fault: transmission shaft damage, oil pump failure, hydraulic oil too dirty or insufficient, motor failure, reducer failure, control rod loose and other reasons.
![全自动混凝土搅拌车](//capemaycitypolice.com/uploadfile/2020/1210/20201210103111230.png)
![全自动混凝土搅拌车](http://capemaycitypolice.com/uploadfile/2020/1210/20201210103111230.png)
三、寻找故障点
3、 Find the fault point
当多功能混凝土搅拌车运送混凝土过程中,发生罐体无法转动故障,应停车进行检查。通过“一听、一看、一动”迅速寻找故障点,“一听”是指从传动轴到减速机各零部件有无发出异响;“一看”是指看液压油箱油位是否过低或管路漏油严重;“一动”是指前后扳动油泵伺服杆,罐体是否正反均无转动。
When the multi-functional concrete mixer truck can't rotate in the process of transporting concrete, it should be stopped for inspection. Through "one listen, one look, one move" to quickly find out the fault point. "One listen" refers to whether the parts from the transmission shaft to the reducer make abnormal noise; "one look" refers to whether the oil level of the hydraulic oil tank is too low or the pipeline has serious oil leakage; "moving" refers to pulling the servo rod of the oil pump back and forth, and whether the tank body does not rotate in both positive and negative directions.
注:应在罐体停止转动后紧急联系当地服务人员(附通讯录),告知罐内混凝土标号及预凝时间,服务人员会耐心指导您如何处理,同时请您将车辆开至就近服务站。
Note: after the tank stops rotating, contact the local service personnel (attached with the address book) to inform the concrete mark number and pre setting time in the tank. The service personnel will guide you how to handle it patiently. At the same time, please drive the vehicle to the nearest service station.
四、应急措施
4、 Emergency measures
如果不能在混凝土预凝之前将自上料混凝土搅拌车修复,应立即采取应急措施:
If the self loading concrete mixer cannot be repaired before the concrete is pre set, emergency measures shall be taken immediately:
1.马达和减速机无故障情况下,连接“应急油管”将混凝土卸出,预防凝灌事故发生。
1. When the motor and reducer have no fault, connect the "emergency oil pipe" to unload the concrete, so as to prevent the occurrence of condensation grouting accident.
2.马达或减速机发生故障且确定无法在混凝土预凝前使罐体转动,请快速打开人孔盖,如人孔盖不在罐体下方则需要在罐体前锥底部开孔(Φ=1250px,避开原有焊道),与此同时必须持续向进料口灌入大量清水,冲刷罐内混凝土,直至罐体下方无混凝土流出,罐内少量残余混凝土需人工进行清理,清理完毕后进行清洗,将割下部分重新焊接到混凝土搅拌车罐体上(安装人孔盖),并打磨喷漆处理。
2. If the motor or reducer fails and it is determined that the tank can not rotate before the concrete is pre set, please quickly open the manhole cover. If the manhole cover is not under the tank body, it is necessary to open a hole at the bottom of the front cone of the tank body (Φ = 1250px, avoid the original weld bead). At the same time, a large amount of clean water must be poured into the feeding port to flush the concrete in the tank until there is no concrete flowing out under the tank body and a small amount of residual in the tank The remaining concrete needs to be cleaned manually. After cleaning, the cut part should be re welded to the tank body of the concrete mixer truck (the manhole cover should be installed) and polished and painted.